Current Classifieds

Automatic Wagon
Date: 06/14/2019 11:22 pm
cam pulley
Date: 05/30/2018 04:56 pm
Looking for a 1980 windshield
Date: 07/30/2020 04:51 pm
1977 Pinto Hatchback Parts

Date: 08/29/2020 05:31 pm
Parting out 77 Bobcat Hatch
Date: 11/06/2017 04:16 pm
WTB Cruising Wagon
Date: 12/07/2016 05:35 pm
Various Pinto stuff for sale.
Date: 11/21/2018 01:56 pm
2.0 Mickey Thompson SUPER RARE Rocker cover and belt guard
Date: 08/22/2017 09:21 pm
Wanted Type 9 5spd Transmission
Date: 07/04/2017 03:26 pm
need 1978 pinto guage cluster
Date: 03/07/2021 07:35 am
Pinto Wagon
Date: 05/25/2018 01:50 pm
78 pinto wagon

Date: 03/03/2020 01:07 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Valve lash  (Read 4742 times)

0 Members and 1 Guest are viewing this topic.

Offline delizious

  • Pinto Member
  • **
  • Posts: 82
  • FeedBack: +0/-0
  • Gender: Female

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Windows User Fifth year Anniversary
Valve lash
« on: July 15, 2009, 05:26:04 PM »
Ok, I'm a little stuck here on this one i have a Chiltons manual american cars from 1966 to 1973 book thats REALLY REALLY OLD and i treat it as if its my bible which it is :D but its not very specific. it says under valve clearance adjustment 2000cc engine-set cold: Valves to adjust to depressed
             .008    .010
   No.1     No.6     No.7
   No.2     No.8     No.3
   No.3     No.2     No.5
   No.5     No.4     No.1


 So im a bit confused from this diagram it shows, can someone elaborate further?


Thanks!
Logged
Lost 1972 Ford Pinto
Gained 1978 Ford Pinto

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Valve lash
« Reply #1 on: July 16, 2009, 05:15:23 AM »
The simplest method is to rotate the engine until the lobe is up and then check that valve's clearance (between the lobe and the follower rocker).  For the stock cam, the cold clearances are 0.008" intake and 0.010" exhaust.

I have not tried it but that table will save some effort by minimizing the engine rotations.  Per the 1974 Ford manual, number the cam lobes 1 thru 8 front to back.  Rotate the engine until the number 1 lobe is down (valve compressed) then set the #6 clearance at 0.008" (intake) and the #7 clearance at 0.010" (exhaust).  Continue down the table until all valves are adjusted.
Logged
Jerry J - Jupiter, Florida

Offline delizious

  • Pinto Member
  • **
  • Posts: 82
  • FeedBack: +0/-0
  • Gender: Female

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Windows User Fifth year Anniversary
Re: Valve lash
« Reply #2 on: July 16, 2009, 01:52:34 PM »
OH! i knew that...my car is a '73
Logged
Lost 1972 Ford Pinto
Gained 1978 Ford Pinto
Pages: [1]   Go Up
« previous next »