Current Classifieds

Bumper, grill and fender wanted
Date: 12/24/2016 04:13 pm
1980 Pinto Pony for sale

Date: 08/21/2021 03:54 pm
2.3 turbo intake (lower)

Date: 07/15/2020 09:29 pm
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
1976 pinto for sale

Date: 01/12/2017 02:08 pm
upholstery for bucket seats
Date: 10/30/2018 08:44 am
1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
72 pinto drag car

Date: 06/22/2017 07:19 am
1977 Pinto for parts

Date: 10/10/2018 06:25 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/18/2017 04:47 pm
Weiand Single plane manifold - for 72 Pinto 4 barrel Carb
Date: 04/25/2017 12:17 pm
Clutch Fork
Date: 03/31/2018 09:12 pm

Author Topic: Holley 5200 metric threaded jets  (Read 4069 times)

0 Members and 1 Guest are viewing this topic.

Offline fastfred

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +3/-0
  • Gender: Male
  • Pinto running gear. Mercedes Gazelle

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Mobile User Windows User Fifth year Anniversary
Holley 5200 metric threaded jets
« on: July 27, 2009, 07:53:46 PM »
Does anyone know where I can get hold of the early metric threaded main jets for the Holley 5200 carbs?

My motor, a 2.3 needs a larger secondary main jet.

thanks   Fred

Offline 72pair

  • Pinto Sr. Member
  • ****
  • Posts: 269
  • FeedBack: +56/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: Holley 5200 metric threaded jets
« Reply #1 on: July 27, 2009, 08:50:14 PM »
Use the old Esslinger trick of putting the stock secondary jet in the primary side, then drill the primary jet 2 # sizes larger than the original secondary size. I ran my 2000cc this way for years with much better performance. You'll just have to get an index of numbered bits. JT 
72 sedan 2.0, c-4 beater now hot 2.0, 4-speed
72 sedan 2.3, t-5, 8" running project
80 Bobcat hatchback 2.3, 4-spd, 97K

Offline Srt

  • Original Pangra Master Builder
  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1339
  • FeedBack: +100/-0
  • Gender: Male

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Linux User Mobile User Windows User 1000 Posts Fifth year Anniversary Photographer
the only substitute for cubic inches is BOOST!!!

Offline fastfred

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +3/-0
  • Gender: Male
  • Pinto running gear. Mercedes Gazelle

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Mobile User Windows User Fifth year Anniversary
Re: Holley 5200 metric threaded jets
« Reply #3 on: July 29, 2009, 08:53:23 AM »
Got over the problem.

As the main jets are metric then the the two jets are numbered 142 and a 132. This means for instance that a 142 is in fact 1.42 millimeters in diameter. I bought a set of numbered drills from Harbor Freight, printed out a coupon from their web site and got all 60 drills for only $9.99.

I sized up the drills in the jets and carefully drilled just one out using the next size up drill.  I put the undrilled jet back in the primary side, the 142, and drilled the 132 with a drill that measured 1.47 millimeters and put it in the secondary.

The car always ran well low down but nesded more gas when the revs got up.

Seems a bit better.

Fred

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Holley 5200 metric threaded jets
« Reply #4 on: August 11, 2009, 12:10:20 AM »
Tap out the carb body and use Holley jets.
Its better to be a has-been, than a never was.